Tweet
Making the Henna Cone
Preparing the henna cone is an acquired skill that will become easier with practice. If you are planning a henna party, make up a dozen cones ahead of time and have them ready.
To make a henna cone, you will need:
(a) Quart-sized plastic zipper freezer bags, heavy-duty plastic freezer bags, or plastic from upper heavy painter's drop Long-bladed scissors cloth.q Transparent adhesive tape
(b) ong-bladed scissors
(c) Transparent adhesive tape
(d) Straight pins
Follow these steps for cutting and folding the cone:
1. Cut off the reclosable top of the freezer bag with scissors. Cut along the side and bottom seams to separate the plastic into two separate sheets. For other plastics, a comfortable cone size can be from 4 inches by 5 inches (10cm by 12.5 cm) to 4 inches by 7 inches (10 cm by 17.5 cm).
Preparing the henna cone is an acquired skill that will become easier with practice. If you are planning a henna party, make up a dozen cones ahead of time and have them ready.
To make a henna cone, you will need:
(a) Quart-sized plastic zipper freezer bags, heavy-duty plastic freezer bags, or plastic from upper heavy painter's drop Long-bladed scissors cloth.q Transparent adhesive tape
(b) ong-bladed scissors
(c) Transparent adhesive tape
(d) Straight pins
Follow these steps for cutting and folding the cone:
1. Cut off the reclosable top of the freezer bag with scissors. Cut along the side and bottom seams to separate the plastic into two separate sheets. For other plastics, a comfortable cone size can be from 4 inches by 5 inches (10cm by 12.5 cm) to 4 inches by 7 inches (10 cm by 17.5 cm).
2. Fold the sheets in half. Holding the open edges with your thumb and index finger, cut across the closed edge. You now have four plastic sheets.
3. Holding the two sheets lengthwise, place your middle finger on the corner of the top one. Bring the opposite diagonal corner to meet the corner you are holding. Wrap the plastic over and over around your middle finger to create a cone.
4. Adapt the size of the up opening and width of the cone by moving your middle inside the plastic sheets. The up should be the tiny diameter of a straight pin.
5. Have several pieces of 1.5-inch (4cm) precut tape ready. Carefully tape down the final plastic corner near the up. Run at least one strip of tape vertically up the entire open seam. Tape as needed to seal the open edges, but do not tape the ends shut. You cone will be about 6 inches (15 cm) long and have an opening that allows just a 2 - finger space at the top.
Applying the design
Have a paper towel handy to clear the tip of the cone from time to time. Remember, the color and design will hold better if the paste is allowed to remain on the skin for at least 1 to 3 hours.
1. Hold the cone between the thumb and your index finger about 1/4 inch (6mm) from its tip. Touch the tip of the cone to the skin. Then lift up to release the henna paste. Trace the outline of the design on the skin, then fill in the details one section at a time.Lefties should begin at the right side of the design and work towards left.
2.As you are working the pattern, keep it moist so that it doesn't peel away. Use a cotton swab or a square to gently apply a lemon sugar solution-3 teaspoon (15 ml) lemon juice mixed with mixed with one teaspoon (5 mg) sugar- to the design. If you can, moisten the henna design every 1/2 hour for three hours.
3. When you are ready to remove the paste, apply any oil - eucalyptus, mustard, avocado, sesame, olive, almond-generously over the design. Then use the edge of a butter knife, a credit card or your finger nails to scrap off the hardened excess.
4. Avoid washing the area of henna design for several hours. After the paste has been removed, smear the area with oil again. Each day apply the body oil to the design; it will help the drawing last longer.Those with darker skin tones might want to reapply the design on the following day for a longer lasting pattern
Have a paper towel handy to clear the tip of the cone from time to time. Remember, the color and design will hold better if the paste is allowed to remain on the skin for at least 1 to 3 hours.
1. Hold the cone between the thumb and your index finger about 1/4 inch (6mm) from its tip. Touch the tip of the cone to the skin. Then lift up to release the henna paste. Trace the outline of the design on the skin, then fill in the details one section at a time.Lefties should begin at the right side of the design and work towards left.
2.As you are working the pattern, keep it moist so that it doesn't peel away. Use a cotton swab or a square to gently apply a lemon sugar solution-3 teaspoon (15 ml) lemon juice mixed with mixed with one teaspoon (5 mg) sugar- to the design. If you can, moisten the henna design every 1/2 hour for three hours.
3. When you are ready to remove the paste, apply any oil - eucalyptus, mustard, avocado, sesame, olive, almond-generously over the design. Then use the edge of a butter knife, a credit card or your finger nails to scrap off the hardened excess.
4. Avoid washing the area of henna design for several hours. After the paste has been removed, smear the area with oil again. Each day apply the body oil to the design; it will help the drawing last longer.Those with darker skin tones might want to reapply the design on the following day for a longer lasting pattern
sigpic 
Comment